Automatic Power OFF (iX1600 / iX1500 / iX1400 / iX1300 / iX500 / iX100 / SV600 / S1300i)

When the ScanSnap is turned on and left unused for the specified time, it will turn itself off automatically.
HINT
  • For iX1600/iX1500/iX1400/iX1300/iX500/SV600/S1300i, a notification informs you 5 minutes before the ScanSnap turns off automatically.
  • For iX100, a notification appears in the following cases:
    • When a USB cable is used for connection, the ScanSnap will turn off automatically five minutes later.
    • When the ScanSnap is powered by the battery, the ScanSnap has turned off automatically.

Turning the ScanSnap back on after the ScanSnap Has Turned off Automatically

iX1600/iX1500

To turn the ScanSnap back on, perform one of the following operations:

  • Press the touch panel of the ScanSnap
  • Close the ADF paper chute (cover) and open it again
HINT
  • To continue using the ScanSnap, reset the time until auto power-off by performing one of the following:

    • Load a document in the ScanSnap
    • Press the touch panel of the ScanSnap
    • Close the ADF paper chute (cover) and open it again
  • When the startup mode of the ScanSnap is set to [Fast], the ScanSnap does not turn off and stays in sleep (power saving) mode.

iX1400/iX500/S1300i

To turn the ScanSnap back on, perform one of the following operations:

  • Press the [Scan] button on the ScanSnap (this will not start scanning)
  • Close the ADF paper chute (cover) and open it again
HINT

To continue using the ScanSnap, reset the time until auto power-off by performing one of the following:

  • Load a document in the ScanSnap
  • Press the [Scan] button on the ScanSnap
  • Close the ADF paper chute (cover) and open it again

iX1300

To turn the ScanSnap back on, perform one of the following operations:

  • Press the [Scan] button on the ScanSnap
  • Close the ADF paper chute (cover) and open it again
HINT
  • Regardless of the setting for the time of the ScanSnap to turn off automatically, if the ADF paper chute (cover) is closed, the ScanSnap is turned off automatically after it is left unused for one minute.
  • To continue using the ScanSnap, reset the time until auto power-off by performing one of the following:
    • Load documents in the ADF paper chute (cover) or insert a document into the manual feeder
    • Press the [Scan] button on the ScanSnap
    • Close the ADF paper chute (cover) and open it again
  • When the startup mode of the ScanSnap is set to [Fast], the ScanSnap does not turn off and stays in sleep (power saving) mode.

iX100

To turn the ScanSnap back on, perform one of the following operations:

  • Press the [Scan/Stop] button on the ScanSnap
  • Close the feed guide and open it again
HINT

To continue using the ScanSnap, reset the time until auto power-off by performing one of the following:

  • Insert a document in the ScanSnap
  • Press the [Scan/Stop] button on the ScanSnap
  • Close the feed guide and open it again

SV600

To turn the ScanSnap back on, perform one of the following operations:

  • Press the [Scan] button on the ScanSnap (this will not start scanning)
  • Press the [Stop] button on the ScanSnap.
HINT

To continue using the ScanSnap, reset the time until auto power-off by pressing the [Scan] button on the ScanSnap.

Changing the ScanSnap's Power Settings

iX1600/iX1500

  1. Press Settings in the home screen on the touch panel of the ScanSnap to display the [Settings] screen.
  2. Press Scanner settings to display the [Scanner settings] screen.
  3. Press [Automatic power off] to display the [Automatic power off] screen.
  4. Press the setting field for [ScanSnap will automatically power off] to display a list.
  5. Change the setting.
  6. Press Home to return to the home screen.

iX1400/iX1300/iX500/iX100/SV600/S1300i

You can change the time of the ScanSnap to turn off automatically or change the setting so that it will not turn off automatically. Set according to the following procedures:

  1. Right-click the ScanSnap Manager icon Communicating in the notification area and select [Preferences] from the Right-Click Menu.
    • The [ScanSnap Manager - Preferences] window appears.
  2. In the [Power] list, change the settings for [Power setting] based on how it is connected.